3A 3.2   A
What is the maximum transmitting power permitted an amateur station on 10.14
MHz?
 
 A. 200 Watts PEP output
 B. 1000 Watts DC input
 C. 1500 Watts PEP output
 D. 2000 Watts DC input
 
 
3A 3.3   A
What is the maximum transmitting power permitted an amateur station on 3725
kHz?
 
 A. 200 watts PEP output
 B. 1000 watts DC input
 C. 1500 watts PEP output
 D. 2000 watts DC input
 
 
3A 3.4   C
What is the maximum transmitting power permitted an amateur station on 7080
kHz?
 
 A. 200 watts PEP output
 B. 1000 watts DC input
 C. 1500 watts PEP output
 D. 2000 watts DC input
 
 
3A 3.5   C
What is the maximum transmitting power permitted an amateur station on 24.95
MHz?
 
 A. 200 watts PEP output
 B. 1000 watts DC input
 C. 1500 watts PEP output
 D. 2000 watts DC input
 
 
3A 3.7   A
What is the maximum transmitting power permitted an amateur station
transmitting on 21.150 MHz?
 
 A. 200 watts PEP output
 B. 1000 watts DC input
 C. 1500 watts DC input
 D. 1500 watts PEP output
 
 
3A 4.1   C
How must a General control operator at a Novice station make the station
identification when transmitting on 7050 kHz in ITU Region 2?
 
 A. The control operator should identify the station with his or her call,
    followed by the word "Controlling" and the Novice call
 B. The control operator should identify the station with his or her call,
    followed by the slant mark "/" (or any suitable word) and the Novice call
 C. The control operator should identify the station with the Novice call,
    followed by the slant mark "/" (or any suitable word) and his or her own
    call
 D. A Novice station should not be operated on 7050 kHz, even with a General
    class control operator
 
 
3A 4.3   C
How must a control operator who has a Technician class license and a
"Certificate of Successful Completion of Examination" for General class
privileges identify the station when transmitting on 14.325 MHz?  (Assume
telephony)
 
 A. General-class privileges do not include 14.325 MHz
 B. No special form of identification is needed
 C. The operator shall give his/her call sign, followed by "slant mark" or any
    suitable word that denotes the slant mark and the identifier "AG"
 D. The operator shall give his/her call sign, followed by the date and
    location of the VEC examination where he/she obtained the upgraded
    license
 
 
3A 6.1   B
Under what circumstances, if any, may third-party communications be
transmitted to a foreign country by an amateur station where the third party
is not eligible to be a control operator of the station?
 
 A. Under no circumstances
 B. Only if the country has a third-party communications agreement with the
    United States
 C. Only if the control operator is an Amateur Extra class licensee
 D. Only if the country has formal diplomatic relations with the United
    states
 
 
3A 6.2   C
What types of messages may be transmitted by an amateur station to a foreign
country for a third-party?
 
 A. Third-party communications involving material compensation, either
    tangible or intangible, direct or indirect, to a third party, a station
    licensee, a control operator, or any other person
 B. Third-party communications facilitating the business affairs of any party
 C. Third-party communications limited to messages of a technical nature or
    remarks of a personal character
 D. No messages may be transmitted to foreign countries for third parties
 
 
3A 6.6   A
Which of the following limitations apply to third-party messages transmitted
to foreign countries where the third party is not eligible to be a control
operator of the station?
 
 A. Third-party messages may only be transmitted to amateurs in countries
    with which the US has a third-party communications agreement
 B. Third-party messages may only be sent to amateurs in ITU Region 1
 C. Third-party messages may only be sent to amateurs in ITU Region 3
 D. Third-party messages must always be transmitted in English
 
 
3A 8.6   D
Under what circumstances, if any, may an amateur station transmitting on 29.64
MHz repeat the 146.34 MHz signals of an amateur station with a Technician
control operator?
 
 A. Under no circumstances
 B. Only if the station on 29.64 MHz is operating under a Special
    Temporary Authorization allowing such retransmission
 C. Only during an FCC-declared general state of communications emergency
 D. Only if the control operator of the repeater transmitter is authorized
    to operate on 29.64 MHz
 
 
3A 9.1   C
What frequency privileges are authorized to General operators in the 160-meter
wavelength band?
 
 A. 1800 to 1900 kHz only
 B. 1900 to 2000 kHz only
 C. 1800 to 2000 kHz only
 D. 1825 to 2000 kHz only
 
 
3A 9.2   A
What frequency privileges are authorized to General operators in the 75/80
meter wavelength band?
 
 A. 3525 to 3750 and 3850 to 4000 kHz only
 B. 3525 to 3775 and 3875 to 4000 kHz only
 C. 3525 to 3750 and 3875 to 4000 kHz only
 D. 3525 to 3775 and 3850 to 4000 kHz only
 
 
3A 9.3   D
What frequency privileges are authorized to General operators in the 40-meter
wavelength band?
 
 A. 7025 to 7175 and 7200 to 7300 kHz only
 B. 7025 to 7175 and 7225 to 7300 kHz only
 C. 7025 to 7150 and 7200 to 7300 kHz only
 D. 7025 to 7150 and 7225 to 7300 kHz only
 
 
3A 9.4   A
What frequency privileges are authorized to General operators in the 30-meter
wavelength band?
 
 A. 10,100 to 10,150 kHz only
 B. 10,105 to 10,150 kHz only
 C. 10,125 to 10,150 kHz only
 D. 10,100 to 10,125 kHz only
 
 
3A 9.5   B
What frequency privileges are authorized to General operators in the 20-meter
wavelength band?
 
 A. 14,025 to 14,100 and 14,175 to 14,350 kHz only
 B. 14,025 to 14,150 and 14,225 to 14,350 kHz only
 C. 14,025 to 14,125 and 14,200 to 14,350 kHz only
 D. 14,025 to 14,175 and 14,250 to 14,350 kHz only
 
 
3A 9.6   C
What frequency privileges are authorized to General operators in the 15-meter
wavelength band?
 
 A. 21,025 to 21,200 and 21,275 to 21,450 kHz only
 B. 21,025 to 21,150 and 21,300 to 21,450 kHz only
 C. 21,025 to 21,200 and 21,300 to 21,450 kHz only
 D. 21,000 to 21,150 and 21,275 to 21,450 kHz only
 
 
3A 9.7   A
What frequency privileges are authorized to General operators in the 12-meter
wavelength band?
 
 A. 24,890 to 24,990 kHz only
 B. 24,890 to 24,975 kHz only
 C. 24,900 to 24,990 kHz only
 D. 24,790 to 24,990 kHz only
 
 
3A 9.8   A
What frequency privileges are authorized to General operators in the 10-meter
wavelength band?
 
 A. 28,000 to 29,700 kHz only
 B. 28,025 to 29,700 kHz only
 C. 28,100 to 29,700 kHz only
 D. 28,025 to 29,600 kHz only
 
 
3A 9.9   C
Which operator licenses authorize privileges on 1820-kHz?
 
 A. Extra only
 B. Extra, Advanced only
 C. Extra, Advanced, General only
 D. Extra, Advanced, General, Technician only
 
 
3A 9.10   B
Which operator licenses authorize privileges on 3950-kHz?
 
 A. Extra, Advanced only
 B. Extra, Advanced, General only
 C. Extra, Advanced, General, Technician only
 D. Extra, Advanced, General, Technician, Novice only
 
 
3A 9.11   C
Which operator licenses authorize privileges on 7230-kHz?
 
 A. Extra only
 B. Extra, Advanced only
 C. Extra, Advanced, General only
 D. Extra, Advanced, General, Technician only
 
 
3A 9.12   A
Which operator licenses authorize privileges on 10.125-MHz?
 
 A. Extra, Advanced, General only
 B. Extra, Advanced only
 C. Extra only
 D. Technician only
 
 
3A 9.13   B
Which operator licenses authorize privileges on 14.325-MHz?
 
 A. Extra, Advanced, General, Technician only
 B. Extra, Advanced, General only
 C. Extra, Advanced only
 D. Extra only
 
 
3A 9.14   C
Which operator licenses authorize privileges on 21.425-MHz?
 
 A. Extra, Advanced, General, Novice only
 B. Extra, Advanced, General, Technician only
 C. Extra, Advanced, General only
 D. Extra, Advanced only
 
 
3A 9.15   C
Which operator licenses authorize privileges on 24.895-MHz?
 
 A. Extra only
 B. Extra, Advanced only
 C. Extra, Advanced, General only
 D. None
 
 
3A 9.16   C
Which operator licenses authorize privileges on 29.616-MHz?
 
 A. Novice, Technician, General, Advanced, Extra only
 B. Technician, General, Advanced, Extra only
 C. General, Advanced, Extra only
 D. Advanced, Extra only
 
 
3A 10.1   A
On what frequencies within the 160-meter wavelength band may phone emissions
be transmitted?
 
 A. 1800 - 2000 kHz only
 B. 1800 - 1900 kHz only
 C. 1900 - 2000 kHz only
 D. 1825 - 1950 kHz only
 
 
3A 10.2   C
On what frequencies within the 80-meter wavelength band may CW emissions be
transmitted?
 
 A. 3500 - 3750 kHz only
 B. 3700 - 3750 kHz only
 C. 3500 - 4000 kHz only
 D. 3890 - 4000 kHz only
 
 
3A 10.3   D
On what frequencies within the 40-meter wavelength band may image emissions be
transmitted?
 
 A. 7225 - 7300 kHz only
 B. 7000 - 7300 kHz only
 C. 7100 - 7150 kHz only
 D. 7150 - 7300 kHz only
 
 
3A 10.4   C
On what frequencies within the 30-meter wavelength band may RTTY emissions be
transmitted?
 
 A. 10.140 - 10.150 MHz only
 B. 10.125 - 10.150 MHz only
 C. 10.100 - 10.150 MHz only
 D. 10.100 - 10.125 MHz only
 
 
3A 10.5   B
On what frequencies within the 20-meter wavelength band may image emissions be
transmitted?
 
 A. 14,200 - 14,300 kHz only
 B. 14,150 - 14,350 kHz only
 C. 14,025 - 14,150 kHz only
 D. 14,150 - 14,300 kHz only
 
 
3A 10.6   C
On what frequencies within the 15-meter wavelength band may image emissions be
transmitted?
 
 A. 21,200 - 21,300 kHz only
 B. 21,350 - 21,450 kHz only
 C. 21,200 - 21,450 kHz only
 D. 21,100 - 21,200 kHz only
 
 
3A 10.7   C
On what frequencies within the 12-meter wavelength band may phone emissions be
transmitted?
 
 A. 24,890 - 24,990 kHz only
 B. 24,890 - 24,930 kHz only
 C. 24,930 - 24,990 kHz only
 D. Phone emissions are not permitted in this band
 
 
3A 10.8   C
On what frequencies within the 10-meter wavelength band may phone emissions be
transmitted?
 
 A. 28,000 - 28,300 kHz only
 B. 29,000 - 29,700 kHz only
 C. 28,300 - 29,700 kHz only
 D. 28,000 - 29,000 kHz only
 
 
3A 13.1   C
What is the maximum sending speed permitted for data emissions below 28 MHz?
 
 A. 56 kilobauds
 B. 19.6 kilobauds
 C. 300 bauds
 D. 1200 bauds
 
 
3A 13.2   D
What is the maximum sending speed permitted for RTTY emissions below 28 MHz?
below 28 MHz?
 
 A. 56 kilobauds
 B. 19.6 kilobauds
 C. 1200 bauds
 D. 300 bauds
 
 
3A 14.3   B
Under what circumstances, if any, may an amateur station engage in some form of
broadcasting?
 
 A. During severe storms, amateurs may broadcast weather information for
    people with scanners
 B. Under no circumstances
 C. If power levels under one watt are used, amateur stations may broadcast
    information bulletins, but not music
 D. Amateur broadcasting is permissible above 10 GHz
 
 
3A 14.6   A
Which of the following is NOT a condition that allows an amateur station to
engage in news gathering for broadcast purposes?
 
 A. The information is more quickly transmitted by Amateur Radio
 B. The information involves the immediate safety of life of individuals or
    the immediate protection of property
 C. The information is directly related to the event
 D. The information cannot be transmitted by other means
 
 
3A 15.1   D
Under what circumstances, if any, may the playing of a violin be transmitted by
an amateur station?
 
 A. When the music played produces no dissonances or spurious emissions
 B. When it is used to jam an illegal transmission
 C. Only above 1215 MHz
 D. Transmitting music is not permitted in the Amateur Service
 
 
3A 15.3   C
Under what circumstances, if any, may the playing of a piano be transmitted by
an amateur station?
 
 A. When it is used to jam an illegal transmission
 B. Only above 1215 MHz
 C. Transmitting music is not permitted in the Amateur Service
 D. When the music played produces no dissonances or spurious emissions
 
 
3A 15.4   B
Under what circumstances, if any, may the playing of a harmonica be transmitted
by an amateur station?
 
 A. When the music played produces no dissonances or spurious emissions
 B. Transmitting music is not permitted in the Amateur Service
 C. When it is used to jam an illegal transmission
 D. Only above 1215 MHz
 
 
3A 16.1   C
Under what circumstances, if any, may an amateur station in two-way
communication transmit a message in a secret code in order to obscure the
meaning of the communication?
 
 A. Only above 450 MHz
 B. Only on Field Day
 C. Never
 D. Only during a declared communications emergency
 
 
3A 16.2   B
In an amateur communication, what types of abbreviations or procedural signals
are not considered codes or ciphers?
 
 A. Abbreviations and procedural signals certified by the ARRL
 B. Abbreviations and signals established by regulation or custom and usage
    and whose intent is to facilitate communication and not to obscure meaning
 C. No abbreviations are permitted, as they tend to obscure the meaning of the
    message to FCC monitoring stations
 D. Only "10 Codes" are permitted
 
 
3A 16.3   A
When, if ever, are codes and ciphers permitted in two-way domestic Amateur
Radio communications?
 
 A. Codes or ciphers are prohibited under all circumstances
 B. Codes or ciphers are permitted during ARRL-sponsored contests
 C. Codes or ciphers are permitted during nationally declared emergencies
 D. Codes or ciphers are permitted above 2.3 GHz
 
 
3A 16.4   A
When, if ever, are codes or ciphers permitted in two-way international Amateur
Radio communications?
 
 A. Codes or ciphers are prohibited under all circumstances
 B. Codes or ciphers are permitted during ITU-sponsored DX contests
 C. Codes or ciphers are permitted during internationally declared
    emergencies
 D. Codes or ciphers are permitted only on frequencies above 2.3 GHz
 
 
3B 1.4   C
What is meant by the term FLATTOPPING in a single-sideband phone transmission?
 
 A. Signal distortion caused by insufficient collector current
 B. The transmitter's automatic level control is properly adjusted
 C. Signal distortion caused by excessive drive
 D. The transmitter's carrier is properly suppressed
 
 
3B 1.5   B
How should the microphone gain control be adjusted on a single-sideband phone
transmitter?
 
 A. For full deflection of the ALC meter on modulation peaks
 B. For slight movement of the ALC meter on modulation peaks
 C. For 100% frequency deviation on modulation peaks
 D. For a dip in plate current
 
 
3B 2.1   B
In what segment of the 20-meter wavelength band do most RTTY transmissions
take place?
 
 A. Between 14.000 and 14.050 MHz
 B. Between 14.075 and 14.100 MHz
 C. Between 14.150 and 14.225 MHz
 D. Between 14.275 and 14.350 MHz
 
 
3B 2.2   A
In what segment of the 80-meter wavelength band do most RTTY transmissions
take place?
 
 A. 3.610 to 3.630 MHz
 B. 3500 to 3525 kHz
 C. 3700 to 3750 kHz
 D. 3.775 to 3.825 MHz
 
 
3B 2.3   C
What is meant by the term BAUDOT?
 
 A. Baudot is a 7-bit code, with start, stop and parity bits
 B. Baudot is a 7-bit code in which each character has four mark and three
    space bits
 C. Baudot is a 5-bit code, with additional start and stop bits
 D. Baudot is a 6-bit code, with additional start, stop and parity bits
 
 
3B 2.4   A
What is meant by the term ASCII?
 
 A. ASCII is a 7-bit code, with additional start, stop and parity bits
 B. ASCII is a 7-bit code in which each character has four mark and three
    space bits
 C. ASCII is a 5-bit code, with additional start and stop bits
 D. ASCII is a 5-bit code in which each character has three mark and two
    space bits
 
 
3B 2.6   B
What is the most common frequency shift for RTTY emissions in the amateur HF
bands?
 
 A. 85 Hz
 B. 170 Hz
 C. 425 Hz
 D. 850 Hz
 
 
3B 2.10   C
What are the two subset modes of AMTOR?
 
 A. A mark of 2125 Hz and a space of 2295 Hz
 B. Baudot and ASCII
 C. ARQ and FEC
 D. USB and LSB
 
 
3B 2.11   D
What is the meaning of the term ARQ?
 
 A. Automatic Repeater Queue
 B. Automatic Receiver Quieting
 C. Automatically Resend Quickly
 D. Automatic Repeat Request
 
 
3B 2.12   B
What is the meaning of the term FEC?
 
 A. Frame Error Check
 B. Forward Error Correction
 C. Frequency Envelope Control
 D. Frequency Encoded Connection
 
 
3B 3.8   A
What is a BAND PLAN?
 
 A. An outline adopted by Amateur Radio operators for operating within a
    specific portion of radio spectrum
 B. An arrangement for deviating from FCC Rules and Regulations
 C. A schedule for operating devised by the Federal Communications Commission
 D. A plan devised for a club on how best to use a band during a contest
 
 
3B 3.12   A
What is the usual input/output frequency separation for a 10 meter station in
repeater operation?
 
 A. 100 kHz
 B. 600 kHz
 C. 1.6 MHz
 D. 170 Hz
 
 
3B 4.1   A
What is meant by the term VOX TRANSMITTER CONTROL?
 
 A. Circuitry that causes the transmitter to transmit automatically when the
    operator speaks into the microphone
 B. Circuitry that shifts the frequency of the transmitter when the
    operator switches from radiotelegraphy to radiotelephony
 C. Circuitry that activates the receiver incremental tuning in a
    transceiver
 D. Circuitry that isolates the microphone from the ambient noise level
 
 
3B 4.2   B
What is the common name for the circuit that causes a transmitter to
automatically transmit when a person speaks into the microphone?
 
 A. VXO
 B. VOX
 C. VCO
 D. VFO
 
 
3B 5.1   D
What is meant by the term FULL BREAK-IN TELEGRAPHY?
 
 A. A system of radiotelegraph communication in which the breaking station
    sends the Morse Code symbols BK
 B. A system of radiotelegraph communication in which only automatic keyers
    can be used
 C. A system of radiotelegraph communication in which the operator must
    activate the send-receive switch after completing a transmission
 D. A system of radiotelegraph communication in which the receiver is
    sensitive to incoming signals between transmitted key pulses
 
 
3B 5.2   C
What Q signal is used to indicate full break-in telegraphy capability?
 
 A. QSB
 B. QSF
 C. QSK
 D. QSV
 
 
3B 6.1   B
When selecting an CW transmitting frequency, what is the minimum frequency
separation from a QSO in progress that should be allowed in order to minimize
interference?
 
 A. 5 to 50 Hz
 B. 150 to 500 Hz
 C. Approximately 3 kHz
 D. Approximately 6 kHz
 
 
3B 6.2   B
When selecting a single-sideband phone transmitting frequency, what is the
minimum frequency separation from a QSO in progress that should be allowed in
order to minimize interference?
 
 A. 150 to 500 Hz between suppressed carriers
 B. Approximately 3 kHz between suppressed carriers
 C. Approximately 6 kHz between suppressed carriers
 D. Approximately 10 kHz between suppressed carriers
 
 
3B 6.3   B
When selecting a RTTY transmitting frequency, what is the minimum frequency
separation from a QSO in progress that should be allowed in order to minimize
interference?
 
 A. Approximately 45 Hz center to center
 B. Approximately 250 to 500 Hz center to center
 C. Approximately 3 kHz center to center
 D. Approximately 6 kHz center to center
 
 
3B 7.1   B
What is an AZIMUTHAL map?
 
 A. A map projection that is always centered on the North Pole
 B. A map projection, centered on a particular location, that determines the
    shortest path between two points on the surface of the earth
 C. A map that shows the angle at which an amateur satellite crosses the
    equator
 D. A map that shows the number of degrees longitude that an amateur
    satellite appears to move westward at the equator with each orbit
 
 
3B 7.2   A
How can an azimuthal map be helpful in conducting international HF radio
communications?
 
 A. It is used to determine the proper beam heading for the shortest path
    to a DX station
 B. It is used to determine the most efficient transmitting antenna height
    to conduct the desired communication
 C. It is used to determine the angle at which an Amateur satellite crosses
    the equator
 D. It is used to determine the maximum usable frequency (MUF)
 
 
3B 7.3   A
What is the most useful type of map when orienting a directional antenna toward
a station 5,000 miles distant?
 
 A. Azimuthal
 B. Mercator
 C. Polar projection
 D. Topographical
 
 
3B 7.4   C
A directional antenna pointed in the long-path direction to another station is
generally oriented how many degrees from the short-path heading?
 
 A. 45 degrees
 B. 90 degrees
 C. 180 degrees
 D. 270 degrees
 
 
3B 7.5   C
What is the short-path heading to Antarctica?
 
 A. Approximately 0 degrees
 B. Approximately 90 degrees
 C. Approximately 180 degrees
 D. Approximately 270 degrees
 
 
3B 8.1   C
When permitted, transmissions to amateur stations in another country must be
limited to only what type of messages?
 
 A. Messages of any type are permitted
 B. Messages that compete with public telecommunications services
 C. Messages of a technical nature or remarks of a personal character of
    relative unimportance
 D. Such transmissions are never permitted
 
 
3B 8.2   B
In which International Telecommunication Union Region is the continental United
States?
 
 A. Region 1
 B. Region 2
 C. Region 3
 D. Region 4
 
 
3B 8.3   B
In which International Telecommunication Union Region is Alaska?
 
 A. Region 1
 B. Region 2
 C. Region 3
 D. Region 4
 
 
3B 8.4   C
In which International Telecommunication Union Region is American Samoa?
 
 A. Region 1
 B. Region 2
 C. Region 3
 D. Region 4
 
 
3B 8.5   C
For uniformity in international radio communication, what time measurement
standard should Amateur Radio operators worldwide use?
 
 A. Eastern Standard Time
 B. Uniform Calibrated Time
 C. Coordinated Universal Time
 D. Universal Time Control
 
 
3B 8.6   B
In which International Telecommunication Union Region is Hawaii?
 
 A. Region 1
 B. Region 2
 C. Region 3
 D. Region 4
 
 
3B 8.7   C
In which International Telecommunication Union Region are the Northern Mariana
Islands?
 
 A. Region 1
 B. Region 2
 C. Region 3
 D. Region 4
 
 
3B 8.8   C
In which International Telecommunication Union Region is Guam?
 
 A. Region 1
 B. Region 2
 C. Region 3
 D. Region 4
 
 
3B 8.9   C
In which International Telecommunication Union Region is Wake Island?
 
 A. Region 1
 B. Region 2
 C. Region 3
 D. Region 4
 
 
3B 10.1   A
What is the AMATEUR AUXILIARY to the FCC's Field Operations Bureau?
 
 A. Amateur Volunteers formally enlisted to monitor the airwaves for rules
    violations
 B. Amateur Volunteers who conduct Amateur Radio licensing examinations
 C. Amateur Volunteers who conduct frequency coordination for amateur VHF
    repeaters
 D. Amateur Volunteers who determine height above average terrain measurements
    for repeater installations
 
 
3B 10.2   B
What are the objectives of the AMATEUR AUXILIARY to the FCC's Field Operations
Bureau?
 
 A. To enforce amateur self-regulation and compliance with the rules
 B. To foster amateur self-regulation and compliance with the rules
 C. To promote efficient and orderly spectrum usage in the repeater
    subbands
 D. To provide emergency and public safety communications
 
 
3C 1.6   C
What is the maximum distance along the earth's surface that can normally be
covered in one hop using the F2 layer?
 
 A. Approximately 180 miles
 B. Approximately 1200 miles
 C. Approximately 2500 miles
 D. No distance. This layer does not support radio communication
 
 
3C 1.7   B
What is the maximum distance along the earth's surface that can be covered in
one hop using the E layer?
 
 A. Approximately 180 miles
 B. Approximately 1200 miles
 C. Approximately 2500 miles
 D. No distance. This layer does not support radio communication
 
 
3C 1.9   B
What is the average height of maximum ionization of the E layer?
 
 A. 45 miles
 B. 70 miles
 C. 200 miles
 D. 1200 miles
 
 
3C 1.10   A
During what part of the day, and in what season of the year can the F2 layer be
expected to reach its maximum height?
 
 A. At noon during the summer
 B. At midnight during the summer
 C. At dusk in the spring and fall
 D. At noon during the winter
 
 
3C 1.13   D
What is the CRITICAL ANGLE, as used in radio wave propagation?
 
 A. The lowest take off angle that will return a radio wave to earth under
    specific ionospheric conditions
 B. The compass direction of the desired DX station from your location
 C. The 180-degree-inverted compass direction of the desired DX station
    from your location
 D. The highest take off angle that will return a radio wave to earth
    during specific ionospheric conditions
 
 
3C 2.3   C
What is the main reason that the 160-, 80- and 40-meter wavelength amateur
bands tend to be useful for only short-distance communications during daylight
hours?
 
 A. Because of a lack of activity
 B. Because of auroral propagation
 C. Because of D-layer absorption
 D. Because of magnetic flux
 
 
3C 2.4   C
What is the principal reason that the 160-meter through 40-meter wavelength
bands are useful only for short-distance radio communications during daylight
hours?
 
 A. F-layer bending
 B. Gamma radiation
 C. D-layer absorption
 D. Tropospheric ducting
 
 
3C 3.3   B
If the maximum usable frequency on the path from Minnesota to Africa is 22
MHz, which band should offer the best chance for a successful QSO?
 
 A. 10 meters
 B. 15 meters
 C. 20 meters
 D. 40 meters
 
 
3C 3.4   C
If the maximum usable frequency on the path from Ohio to West Germany is 17
MHz, which band should offer the best chance for a successful QSO?
 
 A. 80 meters
 B. 40 meters
 C. 20 meters
 D. 2 meters
 
 
3C 5.1   B
Over what periods of time do sudden ionospheric disturbances normally last?
 
 A. The entire day
 B. A few minutes to a few hours
 C. A few hours to a few days
 D. Approximately one week
 
 
3C 5.2   A
What can be done at an amateur station to continue radio communications during
a sudden ionospheric disturbance?
 
 A. Try a higher frequency
 B. Try the other sideband
 C. Try a different antenna polarization
 D. Try a different frequency shift
 
 
3C 5.3   B
What effect does a sudden ionospheric disturbance have on the daylight
ionospheric propagation of HF radio waves?
 
 A. Disrupts higher-latitude paths more than lower-latitude paths
 B. Disrupts transmissions on lower frequencies more than those on higher
    frequencies
 C. Disrupts communications via satellite more than direct communications
 D. None. Only dark (as in nighttime) areas of the globe are affected
 
 
3C 5.4   C
How long does it take a solar disturbance that increases the sun's ultraviolet
radiation to cause ionospheric disturbances on earth?
 
 A. Instantaneously
 B. 1.5 seconds
 C. 8 minutes
 D. 20 to 40 hours
 
 
3C 5.5   A
Sudden ionospheric disturbances cause increased radio wave absorption in which
layer of the ionosphere?
 
 A. D layer
 B. E layer
 C. F1 layer
 D. F2 layer
 
 
3C 6.2   B
What is a characteristic of BACKSCATTER signals?
 
 A. High intelligibility
 B. A wavering sound
 C. Reversed modulation
 D. Reversed sidebands
 
 
3C 6.4   D
What makes backscatter signals often sound distorted?
 
 A. Auroral activity and changes in the earth's magnetic field
 B. The propagation through ground waves that absorb much of the signal's
    clarity
 C. The earth's E-layer at the point of radio wave refraction
 D. The small part of the signal's energy scattered back to the transmitter
    skip zone through several radio-wave paths
 
 
3C 6.5   B
What is the radio wave propagation phenomenon that allows a signal to be
detected at a distance too far for ground wave propagation but too near for
normal sky wave propagation?
 
 A. Ground wave
 B. Scatter
 C. Sporadic-E skip
 D. Short path skip
 
 
3C 6.6   D
When does ionospheric scatter propagation on the HF bands most often occur?
 
 A. When the sunspot cycle is at a minimum
 B. At night
 C. When the F1 and F2 layers are combined
 D. At frequencies above the maximum usable frequency
 
 
3C 7.1   B
What is SOLAR FLUX?
 
 A. The density of the sun's magnetic field
 B. The radio energy emitted by the sun
 C. The number of sunspots on the side of the sun facing the earth
 D. A measure of the tilt of the earth's ionosphere on the side toward the sun
 
 
3C 7.2   D
What is the SOLAR-FLUX INDEX?
 
 A. A measure of past measurements of solar activity
 B. A measurement of solar activity that compares daily readings with results
    from the last six months
 C. Another name for the American sunspot number
 D. A measure of solar activity that is taken daily
 
 
3C 7.3   A
What is a timely indicator of solar activity?
 
 A. The 2800-MHz solar flux index
 B. The mean Canadian sunspot number
 C. A clock set to Coordinated Universal Time
 D. Van Allen radiation measurements taken at Boulder, Colorado
 
 
3C 7.4   D
What type of propagation conditions on the 15-meter wavelength band are
indicated by a solar-flux index value of 60 to 70?
 
 A. Unpredictable ionospheric propagation
 B. No ionospheric propagation is possible
 C. Excellent ionospheric propagation
 D. Poor ionospheric propagation
 
 
3C 7.5   D
A solar-flux index in the range of 90 to 110 indicates what type of
propagation conditions on the 15-meter wavelength band?
 
 A. Poor ionospheric propagation
 B. No ionospheric propagation is possible
 C. Unpredictable ionospheric propagation
 D. Good ionospheric propagation
 
 
3C 7.6   A
A solar-flux index of greater than 120 would indicate what type of propagation
conditions of the 10-meter wavelength band?
 
 A. Good ionospheric propagation
 B. Poor ionospheric propagation
 C. No ionospheric propagation is possible
 D. Unpredictable ionospheric propagation
 
 
3C 7.7   D
For widespread long distance openings on the 6-meter wavelength band, what
solar-flux index values would be required?
 
 A. Less than 50
 B. Approximately 75
 C. Greater than 100
 D. Greater than 250
 
 
3C 7.8   C
If the MUF is high and HF radio communications are generally good for several
days, a similar condition can usually be expected how many days later?
 
 A. 7 days
 B. 14 days
 C. 28 days
 D. 90 days
 
 
3C 10.1   D
What is a GEOMAGNETIC DISTURBANCE?
 
 A. A sudden drop in the solar-flux index
 B. A shifting of the earth's magnetic pole
 C. Ripples in the ionosphere
 D. A dramatic change in the earth's magnetic field over a short period of
    time
 
 
3C 10.2   A
Which latitude paths are more susceptible to geomagnetic disturbances?
 
 A. Those greater than 45 degrees latitude
 B. Those less than 45 degrees latitude
 C. Equatorial paths
 D. All paths are affected equally
 
 
3C 10.3   B
What can be the effect of a major geomagnetic storm on radio communications?
 
 A. Improved high-latitude HF communications
 B. Degraded high-latitude HF communications
 C. Improved ground-wave propagation
 D. Improved chances of ducting at UHF
 
 
3C 10.4   D
How long does it take a solar disturbance that increases the sun's radiation
of charged particles to affect radio wave propagation on earth?
 
 A. The effect is instantaneous
 B. 1.5 seconds
 C. 8 minutes
 D. 20 to 40 hours
 
 
3D 1.5   A
Which wires in a four conductor line cord should be attached to fuses in a 234
VAC primary (single phase) power supply?
 
 A. Only the "hot" (black and red) wires
 B. Only the "neutral" (white) wire
 C. Only the "ground" (bare) wire
 D. All wires
 
 
3D 1.6   A
What size wire is normally used on a 15-ampere, 117-VAC household lighting
circuit?
 
 A. AWG number 14
 B. AWG number 16
 C. AWG number 18
 D. AWG number 22
 
 
3D 1.7   D
What size wire is normally used on a 20-ampere, 117-VAC household appliance
circuit?
 
 A. AWG number 20
 B. AWG number 16
 C. AWG number 14
 D. AWG number 12
 
 
3D 1.8   C
What could be a cause of the room lights dimming when the transmitter is keyed?
 
 A. RF in the AC pole transformer
 B. High resistance in the key contacts
 C. A drop in AC line voltage
 D. The line cord is wired incorrectly
 
 
3D 1.9   D
What size fuse should be used on a #12 wire household appliance circuit?
 
 A. Maximum of 100 amperes
 B. Maximum of 60 amperes
 C. Maximum of 30 amperes
 D. Maximum of 20 amperes
 
 
3D 2.4   B
What safety feature is provided by a bleeder resistor in a power supply?
 
 A. It improves voltage regulation
 B. It discharges the filter capacitors
 C. It removes shock hazards from the induction coils
 D. It eliminates ground-loop current
 
 
3D 3.1   C
What kind of input signal is used to test the amplitude linearity of a single
sideband phone transmitter while viewing the output on an oscilloscope?
 
 A. Normal speech
 B. An audio-frequency sine wave
 C. Two audio-frequency sine waves
 D. An audio-frequency square wave
 
 
3D 3.2   C
To test the amplitude linearity of a single-sideband phone transmitter with an
oscilloscope, what should the audio input to the transmitter be?
 
 A. Normal speech
 B. An audio-frequency sine wave
 C. Two audio-frequency sine waves
 D. An audio-frequency square wave
 
 
3D 3.3   C
How are two tones used to test the amplitude linearity of a single-sideband
phone transmitter?
 
 A. Two harmonically related audio tones are fed into the microphone input
    of the transmitter, and the output is observed on an oscilloscope
 B. Two harmonically related audio tones are fed into the microphone input
    of the transmitter, and the output is observed on a distortion analyzer
 C. Two non-harmonically related audio tones are fed into the microphone
    input of the transmitter, and the output is observed on an oscilloscope
 D. Two non-harmonically related audio tones are fed into the microphone
    input of the transmitter, and the output is observed on a wattmeter
 
 
3D 3.4   D
What audio frequencies are used in a TWO-TONE TEST of the linearity of a
single-sideband phone transmitter?
 
 A. 20 Hz and 20,000 Hz tones must be used
 B. 1200 Hz and 2400 Hz tones must be used
 C. Any two audio tones may be used, but they must be within the transmitter
    audio passband, and must be harmonically related
 D. Any two audio tones may be used, but they must be within the transmitter
    audio passband, and should not be harmonically related
 
 
3D 3.5   D
What can be determined by making a TWO-TONE TEST using an oscilloscope?
 
 A. The percent of frequency modulation
 B. The percent of carrier phase shift
 C. The frequency deviation
 D. The amplifier linearity
 
 
3D 4.1   A
How can the grid-current meter in a power amplifier be used as a neutralizing
indicator?
 
 A. Tune for minimum change in grid current as the output circuit is
    changed
 B. Tune for maximum change in grid current as the output circuit is
    changed
 C. Tune for minimum grid current
 D. Tune for maximum grid current
 
 
3D 4.2   D
Why is neutralization in some vacuum tube amplifiers necessary?
 
 A. To reduce the limits of loaded Q in practical tuned circuits
 B. To reduce grid to cathode leakage
 C. To cancel acid build-up caused by thorium oxide gas
 D. To cancel oscillation caused by the effects of interelectrode capacitance
 
 
3D 4.3   C
How is neutralization of an RF amplifier accomplished?
 
 A. By supplying energy from the amplifier output to the input on alternate
    half cycles
 B. By supplying energy from the amplifier output to the input shifted 360
    degrees out of phase
 C. By supplying energy from the amplifier output to the input shifted 180
    degrees out of phase
 D. By supplying energy from the amplifier output to the input with a
    proper DC bias
 
 
3D 4.4   B
What purpose does a neutralizing circuit serve in an RF amplifier?
 
 A. It controls differential gain
 B. It cancels the effects of positive feedback
 C. It eliminates circulating currents
 D. It reduces incidental grid modulation
 
 
3D 4.5   B
What is the reason for neutralizing the final amplifier stage of a transmitter?
 
 A. To limit the modulation index
 B. To eliminate parasitic oscillations
 C. To cut off the final amplifier during standby periods
 D. To keep the carrier on frequency
 
 
3D 5.1   B
How can the output PEP of a transmitter be determined with an oscilloscope?
 
 A. Measure peak load voltage across a resistive load with an oscilloscope,
    and calculate, using PEP = [(Vp)(Vp)]/(RL)
 B. Measure peak load voltage across a resistive load with an oscilloscope,
    and calculate, using PEP = [(0.707 PEV)(0.707 PEV)]/RL
 C. Measure peak load voltage across a resistive load with an oscilloscope,
    and calculate, using PEP = (Vp)(Vp)(RL)
 D. Measure peak load voltage across a resistive load with an oscilloscope,
    and calculate, using PEP = [(1.414 PEV)(1.414 PEV)]/RL
 
 
3D 5.5   A
What is the output PEP from a transmitter when an oscilloscope shows 200-volts
peak-to-peak across a 50 ohm resistor connected to the transmitter output
terminals?
 
 A. 100 watts
 B. 200 watts
 C. 400 watts
 D. 1000 watts
 
 
3D 5.6   B
What is the output PEP from a transmitter when an oscilloscope shows 500-volts
peak-to-peak across a 50 ohm resistor connected to the transmitter output
terminals?
 
 A. 500 watts
 B. 625 watts
 C. 1250 watts
 D. 2500 watts
 
 
3D 5.7   B
What is the output PEP of an unmodulated carrier transmitter when an average
reading wattmeter connected to the transmitter output terminals indicates 1060
watts?
 
 A. 530 watts
 B. 1060 watts
 C. 1500 watts
 D. 2120 watts
 
 
3D 6.1   D
What item of test equipment contains horizontal and vertical channel
amplifiers?
 
 A. The ohmmeter
 B. The signal generator
 C. The ammeter
 D. The oscilloscope
 
 
3D 6.2   A
What types of signals can an oscilloscope measure?
 
 A. Any time-dependent signal within the bandwidth capability of the
    instrument
 B. Blinker-light signals from ocean-going vessels
 C. International nautical flag signals
 D. Signals created by aeronautical flares
 
 
3D 6.3   D
What is an OSCILLOSCOPE?
 
 A. An instrument that displays the radiation resistance of an antenna
 B. An instrument that displays the SWR on a feed line
 C. An instrument that displays the resistance in a circuit
 D. An instrument that displays signal waveforms
 
 
3D 6.4   B
What can cause phosphor damage to an oscilloscope cathode ray tube?
 
 A. Directly connecting deflection electrodes to the cathode ray tube
 B. Too high an intensity setting
 C. Overdriving the vertical amplifier
 D. Improperly adjusted focus
 
 
3D 9.1   C
What is a SIGNAL TRACER?
 
 A. A direction-finding antenna
 B. An aid for following schematic diagrams
 C. A device for detecting signals in a circuit
 D. A device for drawing signal waveforms
 
 
3D 9.2   A
How is a signal tracer used?
 
 A. To detect the presence of a signal in the various stages of a receiver
 B. To locate a source of interference
 C. To trace the path of a radio signal through the ionosphere
 D. To draw a waveform on paper
 
 
3D 9.3   D
What is a signal tracer normally used for?
 
 A. To identify the source of radio transmissions
 B. To make exact replicas of signals
 C. To give a visual indication of standing waves on open-wire feed lines
 D. To identify an inoperative stage in a radio receiver
 
 
3D 10.1   B
What is the most effective way to reduce or eliminate audio frequency
interference to home entertainment systems?
 
 A. Install bypass inductors
 B. Install bypass capacitors
 C. Install metal oxide varistors
 D. Install bypass resistors
 
 
3D 10.2   B
What should be done when a properly operating amateur station is the source of
interference to a nearby telephone?
 
 A. Make internal adjustments to the telephone equipment
 B. Contact a phone service representative about installing RFI filters
 C. Nothing can be done to cure the interference
 D. Ground and shield the local telephone distribution amplifier
 
 
3D 10.3   C
What sound is heard from a public address system when audio rectification
occurs in response to a nearby single-sideband phone transmission?
 
 A. A steady hum that persists while the transmitter's carrier is on the air
 B. On and off humming or clicking
 C. Distorted speech from the transmitter's signals
 D. Clearly audible speech from the transmitter's signals
 
 
3D 10.4   C
How can the possibility of audio rectification occurring be minimized?
 
 A. By using a solid state transmitter
 B. By using CW emission only
 C. By ensuring all station equipment is properly grounded
 D. By using AM emission only
 
 
3D 10.5   A
What sound is heard from a public address system when audio rectification
occurs in response to a nearby double-sideband phone transmission?
 
 A. Audible, possibly distorted speech from the transmitter signals
 B. On-and-off humming or clicking
 C. Muffled, distorted speech from the transmitter's signals
 D. Extremely loud, severely distorted speech from the transmitter's signals
 
 
3D 12.2   D
What is the reason for using a speech processor with a single-sideband phone
transmitter?
 
 A. A properly adjusted speech processor reduces average transmitter power
    requirements
 B. A properly adjusted speech processor reduces unwanted noise pickup from
    the microphone
 C. A properly adjusted speech processor improves voice frequency fidelity
 D. A properly adjusted speech processor improves signal intelligibility at
    the receiver
 
 
3D 12.3   B
When a transmitter is 100% modulated, will a speech processor increase the
output PEP?
 
 A. Yes
 B. No
 C. It will decrease the transmitter's peak power output
 D. It will decrease the transmitter's average power output
 
 
3D 12.4   C
Under which band conditions should a speech processor not be used?
 
 A. When there is high atmospheric noise on the band
 B. When the band is crowded
 C. When the frequency in use is clear
 D. When the sunspot count is relatively high
 
 
3D 12.5   D
What effect can result from using a speech processor with a single-sideband
phone transmitter?
 
 A. A properly adjusted speech processor reduces average transmitter power
    requirements
 B. A properly adjusted speech processor reduces unwanted noise pickup from
    the microphone
 C. A properly adjusted speech processor improves voice frequency fidelity
 D. A properly adjusted speech processor improves signal intelligibility at
    the receiver
 
 
3D 13.1   A
At what point in a coaxial line should an electronic T-R switch be installed?
 
 A. Between the transmitter and low-pass filter
 B. Between the low-pass filter and antenna
 C. At the antenna feed point
 D. Right after the low-pass filter
 
 
3D 13.2   C
Why is an electronic T-R switch preferable to a mechanical one?
 
 A. Greater receiver sensitivity
 B. Circuit simplicity
 C. Higher operating speed
 D. Cleaner output signals
 
 
3D 13.3   D
What station accessory facilitates QSK operation?
 
 A. Oscilloscope
 B. Audio CW filter
 C. Antenna relay
 D. Electronic TR switch
 
 
3D 14.6   B
What is an antenna NOISE BRIDGE?
 
 A. An instrument for measuring the noise figure of an antenna or other
    electrical circuit
 B. An instrument for measuring the impedance of an antenna or other
    electrical circuit
 C. An instrument for measuring solar flux
 D. An instrument for tuning out noise in a receiver
 
 
3D 14.7   C
How is an antenna noise bridge used?
 
 A. It is connected at the antenna feed point, and the noise is read directly
 B. It is connected between a transmitter and an antenna and tuned for minimum
    SWR
 C. It is connected between a receiver and an unknown impedance and tuned for
    minimum noise
 D. It is connected between an antenna and a Transmatch and adjusted for
    minimum SWR
 
 
3D 15.1   B
How does the emitted waveform from a properly adjusted single-sideband phone
transmitter appear on a monitoring oscilloscope?
 
 A. A vertical line
 B. A waveform that mirrors the input waveform
 C. A square wave
 D. Two loops at right angles
 
 
3D 15.2   A
What is the best instrument for checking the transmitted signal quality from
a CW or single-sideband phone transmitter?
 
 A. A monitor oscilloscope
 B. A field strength meter
 C. A sidetone monitor
 D. A diode probe and an audio amplifier
 
 
3D 15.3   B
What is a MONITORING OSCILLOSCOPE?
 
 A. A device used by the FCC to detect out-of-band signals
 B. A device used to observe the waveform of a transmitted signal
 C. A device used to display SSTV signals
 D. A device used to display signals in a receiver IF stage
 
 
3D 15.4   D
How is a monitoring oscilloscope connected in a station in order to check the
quality of the transmitted signal?
 
 A. Connect the receiver IF output to the vertical-deflection plates of the
    oscilloscope
 B. Connect the transmitter audio input to the oscilloscope vertical input
 C. Connect a receiving antenna directly to the oscilloscope vertical
    input
 D. Connect the transmitter output to the vertical-deflection plates of the
    oscilloscope
 
 
3D 17.2   A
What is the most appropriate instrument to use when determining antenna
horizontal radiation patterns?
 
 A. A field strength meter
 B. A grid-dip meter
 C. A wave meter
 D. A vacuum-tube voltmeter
 
 
3D 17.3   C
What is a FIELD-STRENGTH meter?
 
 A. A device for determining the standing-wave ratio on a transmission line
 B. A device for checking modulation on the output of a transmitter
 C. A device for monitoring relative RF output
 D. A device for increasing the average transmitter output
 
 
3D 17.4   A
What is a simple instrument that can be useful for monitoring relative RF
output during antenna and transmitter adjustments?
 
 A. A field-strength meter
 B. An antenna noise bridge
 C. A multimeter
 D. A Transmatch
 
 
3D 17.5   B
When the power output from a transmitter is increased by four times how should
the S-meter reading on a nearby receiver change?
 
 A. Decrease by approximately one S-unit
 B. Increase by approximately one S-unit
 C. Increase by approximately four S-units
 D. Decrease by approximately four S-units
 
 
3D 17.6   C
By how many times must the power output from a transmitter be increased to
raise the S-meter reading on a nearby receiver from S-8 to S-9?
 
 A. Approximately 2 times
 B. Approximately 3 times
 C. Approximately 4 times
 D. Approximately 5 times
 
 
3E 1.1   C
What is meant by the term IMPEDANCE?
 
 A. The electric charge stored in a capacitor
 B. The opposition to the flow of AC in a circuit containing only
    capacitance
 C. The opposition to the flow of AC in a circuit
 D. The force of repulsion presented to an electric field by another field
    with the same charge
 
 
3E 1.2   C
What is the opposition to the flow of AC in a circuit containing both
resistance and reactance called?
 
 A. Ohm
 B. Joule
 C. Impedance
 D. Watt
 
 
3E 3.1   B
What is meant by the term REACTANCE?
 
 A. Opposition to DC caused by resistors
 B. Opposition to AC caused by inductors and capacitors
 C. A property of ideal resistors in AC circuits
 D. A large spark produced at switch contacts when an inductor is
    de-energized
 
 
3E 3.2   D
What is the opposition to the flow of AC caused by an inductor called?
 
 A. Resistance
 B. Reluctance
 C. Admittance
 D. Reactance
 
 
3E 3.3   D
What is the opposition to the flow of AC caused by a capacitor called?
 
 A. Resistance
 B. Reluctance
 C. Admittance
 D. Reactance
 
 
3E 3.4   D
How does a coil react to AC?
 
 A. As the frequency of the applied AC increases, the reactance decreases
 B. As the amplitude of the applied AC increases, the reactance also
    increases
 C. As the amplitude of the applied AC increases, the reactance decreases
 D. As the frequency of the applied AC increases, the reactance also
    increases
 
 
3E 3.5   A
How does a capacitor react to AC?
 
 A. As the frequency of the applied AC increases, the reactance decreases
 B. As the frequency of the applied AC increases, the reactance increases
 C. As the amplitude of the applied AC increases, the reactance also
    increases
 D. As the amplitude of the applied AC increases, the reactance decreases
 
 
3E 6.1   A
When will a power source deliver maximum output?
 
 A. When the impedance of the load is equal to the impedance of the source
 B. When the SWR has reached a maximum value
 C. When the power supply fuse rating equals the primary winding current
 D. When air wound transformers are used instead of iron core transformers
 
 
3E 6.2   D
What is meant by IMPEDANCE MATCHING?
 
 A. To make the load impedance much greater than the source impedance
 B. To make the load impedance much less than the source impedance
 C. To use a balun at the antenna feed point
 D. To make the load impedance equal to the source impedance
 
 
3E 6.3   D
What occurs when the impedance of an electrical load is equal to the internal
impedance of the power source?
 
 A. The source delivers minimum power to the load
 B. There will be a high SWR condition
 C. No current can flow through the circuit
 D. The source delivers maximum power to the load
 
 
3E 6.4   A
Why is IMPEDANCE MATCHING important in radio work?
 
 A. So the source can deliver maximum power to the load
 B. So the load will draw minimum power from the source
 C. To ensure that there is less resistance than reactance in the circuit
 D. To ensure that the resistance and reactance in the circuit are equal
 
 
3E 7.2   B
What is the unit measurement of reactance?
 
 A. Mho
 B. Ohm
 C. Ampere
 D. Siemens
 
 
3E 7.4   A
What is the unit measurement of impedance?
 
 A. Ohm
 B. Volt
 C. Ampere
 D. Watt
 
 
3E 10.1   A
What is a BEL?
 
 A. The basic unit used to describe a change in power levels
 B. The basic unit used to describe a change in inductances
 C. The basic unit used to describe a change in capacitances
 D. The basic unit used to describe a change in resistances
 
 
3E 10.2   A
What is a DECIBEL?
 
 A. A unit used to describe a change in power levels, equal to 0.1 bel
 B. A unit used to describe a change in power levels, equal to 0.01 bel
 C. A unit used to describe a change in power levels, equal to 10 bels
 D. A unit used to describe a change in power levels, equal to 100 bels
 
 
3E 10.3   D
Under ideal conditions, a barely detectable change in loudness is approximately
how many dB?
 
 A. 12 dB
 B. 6 dB
 C. 3 dB
 D. 1 dB
 
 
3E 10.4   B
A two-times increase in power results in a change of how many dB?
 
 A. Multiplying the original power by 2 gives a new power that is 1 dB
    higher
 B. Multiplying the original power by 2 gives a new power that is 3 dB
    higher
 C. Multiplying the original power by 2 gives a new power that is 6 dB
    higher
 D. Multiplying the original power by 2 gives a new power that is 12 dB
    higher
 
 
3E 10.5   D
An increase of 6 dB results from raising the power by how many times?
 
 A. Multiply the original power by 1.5 to get the new power
 B. Multiply the original power by 2 to get the new power
 C. Multiply the original power by 3 to get the new power
 D. Multiply the original power by 4 to get the new power
 
 
3E 10.6   B
A decrease of 3 dB results from lowering the power by how many times?
 
 A. Divide the original power by 1.5 to get the new power
 B. Divide the original power by 2 to get the new power
 C. Divide the original power by 3 to get the new power
 D. Divide the original power by 4 to get the new power
 
 
3E 10.7   C
A signal strength report is "10 dB over S9". If the transmitter power is
reduced from 1500 watts to 150 watts, what should be the new signal strength
report?
 
 A. S5
 B. S7
 C. S9
 D. S9 plus 5 dB
 
 
3E 10.8   D
A signal strength report is "20 dB over S9". If the transmitter power is
reduced from 1500 watts to 150 watts, what should be the new signal strength
report?
 
 A. S5
 B. S7
 C. S9
 D. S9 plus 10 dB
 
 
3E 10.9   C
A signal strength report is "20 dB over S9". If the transmitter power is
reduced from 1500 watts to 15 watts, what should be the new signal strength
report?
 
 A. S5
 B. S7
 C. S9
 D. S9 plus 10 dB
 
 
3E 12.1   D
If a 1.0-ampere current source is connected to two parallel connected 10 ohm
resistors, how much current passes through each resistor?
 
 A. 10 amperes
 B. 2 amperes
 C. 1 ampere
 D. 0.5 ampere
 
 
3E 12.3   B
In a parallel circuit with a voltage source and several branch resistors, what
relationship does the total current have to the current in the branch circuits?
 
 A. The total current equals the average of the branch current through each
    resistor
 B. The total current equals the sum of the branch current through each
    resistor
 C. The total current decreases as more parallel resistors are added to the
    circuit
 D. The total current is calculated by adding the voltage drops across each
    resistor and multiplying the sum by the total number of all circuit
    resistors
 
 
3E 13.1   B
How many watts of electrical power are being used when a 400-VDC power source
supplies an 800 ohm load?
 
 A. 0.5 watt
 B. 200 watts
 C. 400 watts
 D. 320,000 watts
 
 
3E 13.2   D
How many watts of electrical power are being consumed by a 12-VDC pilot light
which draws 0.2-amperes?
 
 A. 60 watts
 B. 24 watts
 C. 6 watts
 D. 2.4 watts
 
 
3E 13.3   A
How many watts are being dissipated when 7.0-milliamperes flows through 1.25
kilohms?
 
 A. Approximately 61 milliwatts
 B. Approximately 39 milliwatts
 C. Approximately 11 milliwatts
 D. Approximately 9 milliwatts
 
 
3E 14.1   C
How is the total resistance calculated for several resistors in series?
 
 A. The total resistance must be divided by the number of resistors to
    ensure accurate measurement of resistance
 B. The total resistance is always the lowest-rated resistance
 C. The total resistance is found by adding the individual resistances
    together
 D. The tolerance of each resistor must be raised proportionally to the
    number of resistors
 
 
3E 14.2   D
What is the total resistance of two equal, parallel-connected resistors?
 
 A. Twice the resistance of either resistance
 B. The sum of the two resistances
 C. The total resistance cannot be determined without knowing the exact
    resistances
 D. Half the resistance of either resistor
 
 
3E 14.3   A
What is the total inductance of two equal, parallel-connected inductors?
 
 A. Half the inductance of either inductor, assuming no mutual coupling
 B. Twice the inductance of either inductor, assuming no mutual coupling
 C. The sum of the two inductances, assuming no mutual coupling
 D. The total inductance cannot be determined without knowing the exact
    inductances
 
 
3E 14.4   B
What is the total capacitance of two equal, parallel-connected capacitors?
 
 A. Half the capacitance of either capacitor
 B. Twice the capacitance of either capacitor
 C. The value of either capacitor
 D. The total capacitance cannot be determined without knowing the exact
    capacitances
 
 
3E 14.5   B
What is the total resistance of two equal, series-connected resistors?
 
 A. Half the resistance of either resistor
 B. Twice the resistance of either resistor
 C. The value of either resistor
 D. The total resistance cannot be determined without knowing the exact
    resistances
 
 
3E 14.6   B
What is the total inductance of two equal, series-connected inductors?
 
 A. Half the inductance of either inductor, assuming no mutual coupling
 B. Twice the inductance of either inductor, assuming no mutual coupling
 C. The value of either inductor, assuming no mutual coupling
 D. The total inductance cannot be determined without knowing the exact
    inductances
 
 
3E 14.7   A
What is the total capacitance of two equal, series-connected capacitors?
 
 A. Half the capacitance of either capacitor
 B. Twice the capacitance of either capacitor
 C. The value of either capacitor
 D. The total capacitance cannot be determined without knowing the exact
    capacitances
 
 
3E 15.1   C
What is the voltage across a 500 turn secondary winding in a transformer when
the 2250 turn primary is connected to 117-VAC?
 
 A. 2369 volts
 B. 526.5 volts
 C. 26 volts
 D. 5.8 volts
 
 
3E 15.2   A
What is the turns ratio of a transformer to match an audio amplifier having an
output impedance of 200 ohms to a speaker having an impedance of 10 ohms?
 
 A. 4.47 to 1
 B. 14.14 to 1
 C. 20 to 1
 D. 400 to 1
 
 
3E 15.3   A
What is the turns ratio of a transformer to match an audio amplifier having an
output impedance of 600 ohms to a speaker having an impedance of 4 ohms?
 
 A. 12.2 to 1
 B. 24.4 to 1
 C. 150 to 1
 D. 300 to 1
 
 
3E 15.4   D
What is the impedance of a speaker which requires a transformer with a turns
ratio of 24 to 1 to match an audio amplifier having an output impedance of 2000
ohms?
 
 A. 576 ohms
 B. 83.3 ohms
 C. 7.0 ohms
 D. 3.5 ohms
 
 
3E 16.1   B
What is the voltage that would produce the same amount of heat over time in a
resistive element as would an applied sine wave AC voltage?
 
 A. A DC voltage equal to the peak-to-peak value of the AC voltage
 B. A DC voltage equal to the RMS value of the AC voltage
 C. A DC voltage equal to the average value of the AC voltage
 D. A DC voltage equal to the peak value of the AC voltage
 
 
3E 16.2   D
What is the peak-to-peak voltage of a sine wave which has an RMS voltage of 117
volts?
 
 A. 82.7 volts
 B. 165.5 volts
 C. 183.9 volts
 D. 330.9 volts
 
 
3E 16.3   B
A sine wave of 17-volts peak is equivalent to how many volts RMS?
 
 A. 8.5 volts
 B. 12 volts
 C. 24 volts
 D. 34 volts
 
 
3F 1.5   C
What is the effect of an increase in ambient temperature on the resistance of a
carbon resistor?
 
 A. The resistance will increase by 20% for every 10 degrees centigrade
    that the temperature increases
 B. The resistance stays the same
 C. The resistance change depends on the resistor's temperature coefficient
    rating
 D. The resistance becomes time dependent
 
 
3F 2.6   D
What type of capacitor is often used in power supply circuits to filter the
rectified AC?
 
 A. Disc ceramic
 B. Vacuum variable
 C. Mica
 D. Electrolytic
 
 
3F 2.7   D
What type of capacitor is used in power supply circuits to filter transient
voltage spikes across the transformer secondary winding?
 
 A. High-value
 B. Trimmer
 C. Vacuum variable
 D. Suppressor
 
 
3F 3.5   C
How do inductors become self-resonant?
 
 A. Through distributed electromagnetism
 B. Through eddy currents
 C. Through distributed capacitance
 D. Through parasitic hysteresis
 
 
3F 4.1   A
What circuit component can change 120-VAC to 400-VAC?
 
 A. A transformer
 B. A capacitor
 C. A diode
 D. An SCR
 
 
3F 4.2   B
What is the source of energy connected to in a transformer?
 
 A. To the secondary winding
 B. To the primary winding
 C. To the core
 D. To the plates
 
 
3F 4.3   A
When there is no load is attached to the secondary winding of a transformer,
what is the current in the primary winding called?
 
 A. Magnetizing current
 B. Direct current
 C. Excitation current
 D. Stabilizing current
 
 
3F 4.4   D
In what terms are the primary and secondary windings ratings of a power
transformer usually specified?
 
 A. Joules per second
 B. Peak inverse voltage
 C. Coulombs per second
 D. Volts or volt-amperes
 
 
3F 5.1   C
What is the PEAK-INVERSE-VOLTAGE rating of a power supply rectifier?
 
 A. The highest transient voltage the diode will handle
 B. 1.4 times the AC frequency
 C. The maximum voltage to be applied in the non-conducting direction
 D. 2.8 times the AC frequency
 
 
3F 5.2   B
Why must silicon rectifier diodes be thermally protected?
 
 A. Because of their proximity to the power transformer
 B. Because they will be destroyed if they become too hot
 C. Because of their susceptibility to transient voltages
 D. Because of their use in high-voltage applications
 
 
3F 5.4   D
What are the two major ratings for silicon diode rectifiers of the type used
in power supply circuits which must not be exceeded?
 
 A. Peak load impedance; peak voltage
 B. Average power; average voltage
 C. Capacitive reactance; avalanche voltage
 D. Peak inverse voltage; average forward current
 
 
3G 1.1   A
Why should a resistor and capacitor be wired in parallel with power supply
rectifier diodes?
 
 A. To equalize voltage drops and guard against transient voltage spikes
 B. To ensure that the current through each diode is about the same
 C. To smooth the output waveform
 D. To decrease the output voltage
 
 
3G 1.2   C
What function do capacitors serve when resistors and capacitors are connected
in parallel with high voltage power supply rectifier diodes?
 
 A. They double or triple the output voltage
 B. They block the alternating current
 C. They protect those diodes that develop back resistance faster than other
    diodes
 D. They regulate the output voltage
 
 
3G 1.3   D
What is the output waveform of an unfiltered full-wave rectifier connected to
a resistive load?
 
 A. A steady DC voltage
 B. A sine wave at half the frequency of the AC input
 C. A series of pulses at the same frequency as the AC input
 D. A series of pulses at twice the frequency of the AC input
 
 
3G 1.4   B
How many degrees of each cycle does a half-wave rectifier utilize?
 
 A. 90 degrees
 B. 180 degrees
 C. 270 degrees
 D. 360 degrees
 
 
3G 1.5   D
How many degrees of each cycle does a full-wave rectifier utilize?
 
 A. 90 degrees
 B. 180 degrees
 C. 270 degrees
 D. 360 degrees
 
 
3G 1.6   A
Where is a power supply bleeder resistor connected?
 
 A. Across the filter capacitor
 B. Across the power-supply input
 C. Between the transformer primary and secondary
 D. Across the inductor in the output filter
 
 
3G 1.7   D
What components comprise a power supply filter network?
 
 A. Diodes
 B. Transformers and transistors
 C. Quartz crystals
 D. Capacitors and inductors
 
 
3G 1.8   D
What should be the peak-inverse-voltage rating of the rectifier in a full-wave
power supply?
 
 A. One-quarter the normal output voltage of the power supply
 B. Half the normal output voltage of the power supply
 C. Equal to the normal output voltage of the power supply
 D. Double the normal peak output voltage of the power supply
 
 
3G 1.9   D
What should be the peak-inverse-voltage rating of the rectifier in a half-wave
power supply?
 
 A. One-quarter to one-half the normal peak output voltage of the power supply
 B. Half the normal output voltage of the power supply
 C. Equal to the normal output voltage of the power supply
 D. One to two times the normal peak output voltage of the power supply
 
 
3G 2.8   B
What should the impedance of a low-pass filter be as compared to the impedance
of the transmission line into which it is inserted?
 
 A. Substantially higher
 B. About the same
 C. Substantially lower
 D. Twice the transmission line impedance
 
 
3H 2.1   D
What is the term for alteration of the amplitude of an RF wave for the purpose
of conveying information?
 
 A. Frequency modulation
 B. Phase modulation
 C. Amplitude rectification
 D. Amplitude modulation
 
 
3H 2.3   B
What is the term for alteration of the phase of an RF wave for the purpose of
conveying information?
 
 A. Pulse modulation
 B. Phase modulation
 C. Phase rectification
 D. Amplitude modulation
 
 
3H 2.4   D
What is the term for alteration of the frequency of an RF wave for the purpose
of conveying information?
 
 A. Phase rectification
 B. Frequency rectification
 C. Amplitude modulation
 D. Frequency modulation
 
 
3H 3.1   D
In what emission type does the instantaneous amplitude (envelope) of the RF
signal vary in accordance with the modulating AF?
 
 A. Frequency shift keying
 B. Pulse modulation
 C. Frequency modulation
 D. Amplitude modulation
 
 
3H 3.2   A
What determines the spectrum space occupied by each group of sidebands
generated by a correctly operating double-sideband phone transmitter?
 
 A. The audio frequencies used to modulate the transmitter
 B. The phase angle between the audio and radio frequencies being mixed
 C. The radio frequencies used in the transmitter's VFO
 D. The CW keying speed
 
 
3H 4.1   C
How much is the carrier suppressed in a single-sideband phone transmission?
 
 A. No more than 20 dB below peak output power
 B. No more than 30 dB below peak output power
 C. At least 40 dB below peak output power
 D. At least 60 dB below peak output power
 
 
3H 4.2   C
What is one advantage of carrier suppression in a double-sideband phone
transmission?
 
 A. Only half the bandwidth is required for the same information content
 B. Greater modulation percentage is obtainable with lower distortion
 C. More power can be put into the sidebands
 D. Simpler equipment can be used to receive a double-sideband suppressed-
    carrier signal
 
 
3H 5.1   A
Which one of the telephony emissions popular with amateurs occupies the
narrowest band of frequencies?
 
 A. Single-sideband emission
 B. Double-sideband emission
 C. Phase-modulated emission
 D. Frequency-modulated emission
 
 
3H 5.2   C
Which emission type is produced by a telephony transmitter having a balanced
modulator followed by a 2.5-kHz bandpass filter?
 
 A. PM
 B. AM
 C. SSB
 D. FM
 
 
3H 7.2   B
What emission is produced by a reactance modulator connected to an RF power
amplifier?
 
 A. Multiplex modulation
 B. Phase modulation
 C. Amplitude modulation
 D. Pulse modulation
 
 
3H 8.1   D
What purpose does the carrier serve in a double-sideband phone transmission?
 
 A. The carrier separates the sidebands so they don't cancel in the
    receiver
 B. The carrier contains the modulation information
 C. The carrier maintains symmetry of the sidebands to prevent distortion
 D. The carrier serves as a reference signal for demodulation by an envelope
    detector
 
 
3H 8.2   C
What signal component appears in the center of the frequency band of a double-
sideband phone transmission?
 
 A. The lower sidebands
 B. The subcarrier
 C. The carrier
 D. The pilot tone
 
 
3H 9.1   C
What sidebands are generated by a double-sideband phone transmitter with a
7250-kHz carrier when it is modulated less than 100% by an 800-Hz pure sine
wave?
 
 A. 7250.8 kHz and 7251.6 kHz
 B. 7250.0 kHz and 7250.8 kHz
 C. 7249.2 kHz and 7250.8 kHz
 D. 7248.4 kHz and 7249.2 kHz
 
 
3H 10.1   B
How many times over the maximum deviation is the bandwidth of an FM-phone
transmission?
 
 A. 1.5
 B. At least 2
 C. At least 4
 D. The bandwidth cannot be determined without knowing the exact carrier and
    modulating frequencies involved
 
 
3H 10.2   D
What is the total bandwidth of an FM-phone transmission having a 5-kHz
deviation and a 3-kHz modulating frequency?
 
 A. 3 kHz
 B. 5 kHz
 C. 8 kHz
 D. 16 kHz
 
 
3H 11.1   A
What happens to the shape of the RF envelope, as viewed on an oscilloscope,
during double-sideband phone transmission?
 
 A. The amplitude of the envelope increases and decreases in proportion to
    the modulating signal
 B. The amplitude of the envelope remains constant
 C. The brightness of the envelope increases and decreases in proportion to
    the modulating signal
 D. The frequency of the envelope increases and decreases in proportion to
    the modulating signal
 
 
3H 13.1   D
What results when a single-sideband phone transmitter is overmodulated?
 
 A. The signal becomes louder with no other effects
 B. The signal occupies less bandwidth with poor high frequency response
 C. The signal has higher fidelity and improved signal-to-noise ratio
 D. The signal becomes distorted and occupies more bandwidth
 
 
3H 13.2   B
What results when a double-sideband phone transmitter is overmodulated?
 
 A. The signal becomes louder with no other effects
 B. The signal becomes distorted and occupies more bandwidth
 C. The signal occupies less bandwidth with poor high frequency response
 D. The transmitter's carrier frequency deviates
 
 
3H 15.1   B
What is the frequency deviation for a 12.21-MHz reactance-modulated oscillator
in a 5-kHz deviation, 146.52-MHz FM-phone transmitter?
 
 A. 41.67 Hz
 B. 416.7 Hz
 C. 5 kHz
 D. 12 kHz
 
 
3H 15.2   A
What stage in a transmitter would translate a 5.3-MHz input signal to 14.3
MHz?
 
 A. A mixer
 B. A beat frequency oscillator
 C. A Frequency multiplier
 D. A linear translator
 
 
3H 16.4   A
How many frequency components are in the signal from an AF shift keyer at any
instant?
 
 A. One
 B. Two
 C. Three
 D. Four
 
 
3H 16.5   C
How is frequency shift related to keying speed in an FSK signal?
 
 A. The frequency shift in Hertz must be at least four times the keying
    speed in WPM
 B. The frequency shift must not exceed 15 Hz per WPM of keying speed
 C. Greater keying speeds require greater frequency shifts
 D. Greater keying speeds require smaller frequency shifts
 
 
3I 1.3   C
Why is a Yagi antenna often used for radio communications on the 20-meter
wavelength band?
 
 A. It provides excellent omnidirectional coverage in the horizontal plane
 B. It is smaller, less expensive and easier to erect than a dipole or
    vertical Antenna
 C. It discriminates against interference from other stations off to the
    side or behind
 D. It provides the highest possible angle of radiation for the HF bands
 
 
3I 1.7   D
What method is best suited to match an unbalanced coaxial feed line to a Yagi
antenna?
 
 A. "T" match
 B. Delta match
 C. Hairpin match
 D. Gamma match
 
 
3I 1.9   A
How can the bandwidth of a parasitic beam antenna be increased?
 
 A. Use larger diameter elements
 B. Use closer element spacing
 C. Use traps on the elements
 D. Use tapered-diameter elements
 
 
3I 2.1   C
How much gain over a half-wave dipole can a two-element cubical quad antenna
provide?
 
 A. Approximately 0.6 dB
 B. Approximately 2 dB
 C. Approximately 6 dB
 D. Approximately 12 dB
 
 
3I 3.1   B
How long is each side of a cubical quad antenna driven element for 21.4-MHz?
 
 A. 1.17 feet
 B. 11.7 feet
 C. 47 feet
 D. 469 feet
 
 
3I 3.2   B
How long is each side of a cubical quad antenna driven element for 14.3-MHz?
 
 A. 1.75 feet
 B. 17.6 feet
 C. 23.4 feet
 D. 70.3 feet
 
 
3I 3.3   B
How long is each side of a cubical quad antenna reflector element for 29.6-MHz?
 
 A. 8.23 feet
 B. 8.7 feet
 C. 9.7 feet
 D. 34.8 feet
 
 
3I 3.4   C
How long is each leg of a symmetrical delta loop antenna driven element for
28.7-MHz?
 
 A. 8.75 feet
 B. 11.32 feet
 C. 11.7 feet
 D. 35 feet
 
 
3I 3.5   C
How long is each leg of a symmetrical delta loop antenna driven element for
24.9-MHz?
 
 A. 10.09 feet
 B. 13.05 feet
 C. 13.45 feet
 D. 40.36 feet
 
 
3I 3.6   C
How long is each leg of a symmetrical delta loop antenna reflector element for
14.1-MHz?
 
 A. 18.26 feet
 B. 23.76 feet
 C. 24.35 feet
 D. 73.05 feet
 
 
3I 3.7   B
How long is the driven element of a Yagi antenna for 14.0-MHz?
 
 A. Approximately 17 feet
 B. Approximately 33 feet
 C. Approximately 35 feet
 D. Approximately 66 feet
 
 
3I 3.8   B
How long is the director element of a Yagi antenna for 21.1-MHz?
 
 A. Approximately 42 feet
 B. Approximately 21 feet
 C. Approximately 17 feet
 D. Approximately 10.5 feet
 
 
3I 3.9   C
How long is the reflector element of a Yagi antenna for 28.1-MHz?
 
 A. Approximately 8.75 feet
 B. Approximately 16.6 feet
 C. Approximately 17.5 feet
 D. Approximately 35 feet
 
 
3I 5.1   D
What is the feed-point impedance for a half-wavelength dipole HF antenna
suspended horizontally one-quarter wavelength or more above the ground?
 
 A. Approximately 50 ohms, resistive
 B. Approximately 73 ohms, resistive and inductive
 C. Approximately 50 ohms, resistive and capacitive
 D. Approximately 73 ohms, resistive
 
 
3I 5.2   B
What is the feed-point impedance of a quarter-wavelength vertical HF antenna
with a horizontal ground plane?
 
 A. Approximately 18 ohms
 B. Approximately 36 ohms
 C. Approximately 52 ohms
 D. Approximately 72 ohms
 
 
3I 5.3   D
What is the advantage of downward sloping radials on a ground plane antenna?
 
 A. Sloping the radials downward lowers the radiation angle
 B. Sloping the radials downward brings the feed-point impedance closer to
    300 ohms
 C. Sloping the radials downward allows rainwater to run off the antenna
 D. Sloping the radials downward brings the feed-point impedance closer to
    50 ohms
 
 
3I 5.4   B
What happens to the feed-point impedance of a ground-plane antenna when the
radials slope downward from the base of the antenna?
 
 A. The feed-point impedance decreases
 B. The feed-point impedance increases
 C. The feed-point impedance stays the same
 D. The feed-point impedance becomes purely capacitive
 
 
3I 6.1   C
Compared to a dipole antenna, what are the directional radiation
characteristics of a cubical quad HF antenna?
 
 A. The quad has more directivity in the horizontal plane but less
    directivity in the vertical plane
 B. The quad has less directivity in the horizontal plane but more
    directivity in the vertical plane
 C. The quad has more directivity in both horizontal and vertical planes
 D. The quad has less directivity in both horizontal and vertical planes
 
 
3I 6.2   A
What is the radiation pattern of an ideal half-wavelength dipole HF antenna?
 
 A. If it is installed parallel to the earth, it radiates well in a figure
    eight pattern at right angles to the antenna wire
 B. If it is installed parallel to the earth, it radiates well in a figure
    eight pattern off both ends of the antenna wire
 C. If it is installed parallel to the earth, it radiates equally well in all
    directions
 D. If it is installed parallel to the earth, the pattern will have two lobes
    on one side of the antenna wire and one larger lobe on the other side
 
 
3I 6.3   B
How does proximity to the ground affect the radiation pattern of a horizontal
dipole HF antenna?
 
 A. If the antenna is too far from the ground, the pattern becomes
    unpredictable
 B. If the antenna is less than one-half wavelength from the ground, reflected
    radio waves from the ground distort the radiation pattern of the antenna
 C. A dipole antenna's radiation pattern is unaffected by its distance to the
    ground
 D. If the antenna is less than one half wavelength from the ground, radiation
    off the ends of the wire is reduced
 
 
3I 6.4   C
What does the term ANTENNA FRONT-TO-BACK RATIO mean?
 
 A. The number of directors versus the number of reflectors
 B. The relative position of the driven element with respect to the reflectors
    and directors
 C. The power radiated in the major radiation lobe compared to the power
    radiated in exactly the opposite direction
 D. The power radiated in the major radiation lobe compared to the power
    radiated 90 degrees away from that direction
 
 
3I 6.5   D
What effect upon the radiation pattern of an HF dipole antenna will a slightly
smaller parasitic parallel element located a few feet away in the same
horizontal plane have?
 
 A. The radiation pattern will not change appreciably
 B. A major lobe will develop in the horizontal plane, parallel to the two
    elements
 C. A major lobe will develop in the vertical plane, away from the ground
 D. If the spacing is greater than 0.1 wavelength, a major lobe will
    develop in the horizontal plane to the side of the driven element
    toward the parasitic element
 
 
3I 6.6   C
What is the meaning of the term MAIN LOBE as used in reference to a directional
antenna?
 
 A. The direction of least radiation from an antenna
 B. The point of maximum current in a radiating antenna element
 C. The direction of maximum radiated field strength from a radiating
    antenna
 D. The maximum voltage standing wave point on a radiating element
 
 
3I 7.1   A
Upon what does the characteristic impedance of a parallel-conductor antenna
feed line depend?
 
 A. The distance between the centers of the conductors and the radius of the
    conductors
 B. The distance between the centers of the conductors and the length of the
    line
 C. The radius of the conductors and the frequency of the signal
 D. The frequency of the signal and the length of the line
 
 
3I 7.2   B
What is the characteristic impedance of various coaxial cables commonly used
for antenna feed lines at amateur stations?
 
 A. Around 25 and 30 ohms
 B. Around 50 and 75 ohms
 C. Around 80 and 100 ohms
 D. Around 500 and 750 ohms
 
 
3I 7.3   A
What effect, if any, does the length of a coaxial cable have upon its
characteristic impedance?
 
 A. The length has no effect on the characteristic impedance
 B. The length affects the characteristic impedance primarily above 144
    MHz
 C. The length affects the characteristic impedance primarily below 144
    MHz
 D. The length affects the characteristic impedance at any frequency
 
 
3I 7.4   D
What is the characteristic impedance of flat-ribbon TV-type twinlead?
 
 A. 50 ohms
 B. 75 ohms
 C. 100 ohms
 D. 300 ohms
 
 
3I 8.4   C
What is the cause of power being reflected back down an antenna feed line?
 
 A. Operating an antenna at its resonant frequency
 B. Using more transmitter power than the antenna can handle
 C. A difference between feed line impedance and antenna feed point
    impedance
 D. Feeding the antenna with unbalanced feed line
 
 
3I 9.3   A
What will be the standing wave ratio when a 50 ohm feed line is connected to a
resonant antenna having a 200 ohm feed-point impedance?
 
 A. 4:1
 B. 1:4
 C. 2:1
 D. 1:2
 
 
3I 9.4   D
What will be the standing wave ratio when a 50 ohm feed line is connected to a
resonant antenna having a 10 ohm feed-point impedance?
 
 A. 2:1
 B. 50:1
 C. 1:5
 D. 5:1
 
 
3I 9.5   C
What will be the standing wave ratio when a 50 ohm feed line is connected to a
resonant antenna having a 50 ohm feed-point impedance?
 
 A. 2:1
 B. 50:50
 C. 1:1
 D. 0:0
 
 
3I 11.1   C
How does the characteristic impedance of a coaxial cable affect the amount of
attenuation to the RF signal passing through it?
 
 A. The attenuation is affected more by the characteristic impedance at
    frequencies above 144 MHz than at frequencies below 144 MHz
 B. The attenuation is affected less by the characteristic impedance at
    frequencies above 144 MHz than at frequencies below 144 MHz
 C. The attenuation related to the characteristic impedance is about the
    same at all amateur frequencies below 1.5 GHz
 D. The difference in attenuation depends on the emission type in use
 
 
3I 11.2   A
How does the amount of attenuation to a 2 meter signal passing through a
coaxial cable differ from that to a 160 meter signal?
 
 A. The attenuation is greater at 2 meters
 B. The attenuation is less at 2 meters
 C. The attenuation is the same at both frequencies
 D. The difference in attenuation depends on the emission type in use
 
 
3I 11.4   D
What is the effect on its attentuation when flat-ribbon TV-type twinlead is
wet?
 
 A. Attenuation decreases slightly
 B. Attenuation remains the same
 C. Attenuation decreases sharply
 D. Attenuation increases
 
 
3I 11.7   B
Why might silicone grease or automotive car wax be applied to flat-ribbon
TV-type twinlead?
 
 A. To reduce "skin effect" losses on the conductors
 B. To reduce the buildup of dirt and moisture on the feed line
 C. To increase the velocity factor of the feed line
 D. To help dissipate heat during high-SWR operation
 
 
3I 11.8   D
In what values are RF feed line losses usually expressed?
 
 A. Bels/1000 ft
 B. dB/1000 ft
 C. Bels/100 ft
 D. dB/100 ft
 
 
3I 11.10   D
As the operating frequency increases, what happens to the dielectric losses
in a feed line?
 
 A. The losses decrease
 B. The losses decrease to zero
 C. The losses remain the same
 D. The losses increase
 
 
3I 11.12   A
As the operating frequency decreases, what happens to the dielectric losses
in a feed line?
 
 A. The losses decrease
 B. The losses increase
 C. The losses remain the same
 D. The losses become infinite
 
 
3I 12.1   D
What condition must be satisfied to prevent standing waves of voltage and
current on an antenna feed line?
 
 A. The antenna feed point must be at DC ground potential
 B. The feed line must be an odd number of electrical quarter wavelengths
    long
 C. The feed line must be an even number of physical half wavelengths long
 D. The antenna feed point impedance must be matched to the characteristic
    impedance of the feed line
 
 
3I 12.2   A
How is an inductively-coupled matching network used in an antenna system
consisting of a center-fed resonant dipole and coaxial feed line?
 
 A. An inductively coupled matching network is not normally used in a
    resonant antenna system
 B. An inductively coupled matching network is used to increase the SWR to
    an acceptable level
 C. An inductively coupled matching network can be used to match the
    unbalanced condition at the transmitter output to the balanced
    condition required by the coaxial line
 D. An inductively coupled matching network can used at the antenna feed
    point to tune out the radiation resistance
 
 
3I 12.5   D
What is an antenna-transmission line MISMATCH?
 
 A. A condition where the feed-point impedance of the antenna does not equal
    the output impedance of the transmitter
 B. A condition where the output impedance of the transmitter does not
    equal the characteristic impedance of the feed line
 C. A condition where a half-wavelength antenna is being fed with a
    transmission line of some length other than one-quarter wavelength at
    the operating frequency
 D. A condition where the characteristic impedance of the feed line does
    not equal the feed-point impedance of the antenna
